| |
| TapMaster is an assembly of two basic components - the valve block that connects in-line to the hot and/or cold water lines and the pilot/actuator valve that activates the unit. A standard TapMaster consists of two valve blocks one for each hot and cold water line and one pilot/actuator valve that may use a cabinet door or foot activator. The versatility and adaptability of this component design allows for a variety of configuration to suit virtually any faucet/sink arrangement.
No electrical, no batteries, no electronics. TapMaster operates using water pressure in existing water lines. Installation hardware and detailed instructions included. 5 year limited warranty |
Hands - Free Faucet Controller
-
Add-on for conventional water faucets where flow rate & temperature are pre-set on faucet.
-
Can be used with intermittent on-off or continuous-on without constant foot pressure.
-
Activator requires 4 inch toe-kick under sink cabinet
-
Hands free operation reduces cross-contamination
-
Installation kit is complete & has excellent instructions.
-
86% of 14 CRA Evaluators stated this product would replace products they use currently, & 93% rated it excellent or good; worthy of trial by colleagues (CRA news letter volume 26, issue 2, February 2002, Page 4)
-
Works on water pressure alone-no power outlets , batteries or compressed air required
-
Hands free continuous flow for kick pedal models only
-
Plated solid brass valve blocks
-
High pressure control tubing with protective sheath
-
Built-in protection for water borne debris
-
Completely assembled
-
Installation hardware and instructions included
Foot Activated Models
Kick plate models mount on cabinet toe kicks. Set faucet open at the flow and temperature desired; press foot lightly against vertical face of the kick plate to activate water flow and release to stop it. For continuous flow press down on the angled face to latch; to release press the vertical face. Kick plate is made from 18 gauge stainless steel.
| Item # |
Description |
Price |
| 1740 |
Kick Plate Activation for single water line |
$247.00 |
| 1742 |
Dual Kick Plates for single water line |
$395.00 |
| 1750 |
Standard Kick Plate Activation for hot and cold water lines |
$345.00 |
| 1752 |
Dual Kick Plate Activated for Island Cabinet |
$498.00 |
Euro Foot Activated Models
Euro models mount on cabinet toe kicks. Set Faucet open at the flow and temperature desired; push Euro foot activator in any direction for momentary water flow, release to turn off. For continuous water flow, push Euro foot activator sideways to 45 degrees in either direction to lock on; push activator back to vertical rest position to turn off. Finishes available: Chrome or Brushed Nickel.
| Item # |
Description |
Price |
| 1770 |
Euro style with Momentary Actuator - for hot & cold water lines |
$325.00 |
| 1771 |
Euro Style with Momentary Actuator - Single Water line |
$229.00 |
| 1775 |
Euro Style with locking actuator - hot and cold water lines |
$345.00 |
| 1776 |
Euro Style with locking Actuator - Single Water line |
$249.00 |
Cabinet Door Models
 
These models utilize the cabinet door as the activator by pressing the
button valve mounted on the inside cabinet wall opposite the door hinge.
Set the faucet open at the flow and temperature desired; press knee lightly against
the cabinet door to activate water flow and release to stop it.
| Item # |
Description |
Price |
| 1710 |
Cabinet door activation for single water line |
$206.00 |
| 1720 |
Standard Cabinet Door Activation |
$302.00 |
| 1722 |
Dual Door Activation for Island Cabinet |
$409.00 |
Floor Foot Pedal Models
Floor foot pedal models are designed for a variety of applications including wall mounted sinks, sinks in cabinets with or without toe kicks, or any non typical sink arrangements. Floor foot pedals are made from 18 gauge stainless steel and are operated either from the floor or mounted on a vertical face and used as a kick plate.
| Item # |
Description |
Price |
| 1760 |
Floor Foot Pedal |
$345.00 |
| 1762 |
Dual Floor Foot Pedal for island cabinet |
$498.00 |
Combination Kick Plate & Door Activation Model
The model 1751 offers you the best of both worlds. It is a combination of the models 1750/1720 and is used in cabinet or island situations. Set the faucet open at the flow and temperature desired: press your foot against a kick plate or your knee against the cabinet door to activate water flow and release it to stop. Kick plate is made from 18 gauge stainless steel.
| Item # |
Description |
Price |
| 1751 |
Combination Kick plate & door activation |
$477.00 |
SPECIFICATIONS
| Dimensions: |
Valve Block (less tubing fittings) |
2.26" x .88" x 1.25" (5.74 x 2.24 x 3.18cm) |
| Button Valve (less fittings) |
.63" x .63" x 1.0" (1.60 x 1.60 x 2.54cm) |
| Kick Plate (1750, 1752, 1740, 1742) |
8.0"w x 3.42"h, 1.14"d (20.32 x 8.64 x 2.90cm) |
| Floor Foot Pedal (1760, 1762) |
7.1"w x 3.0"h x 1.1"d (18 x 7.6 x 2.8 cm) |
| Euro Foot Activated |
|
| (1770, 1771, 1775, 1776) |
1.19"w x 4.92"h x 1.37"d (30 x 125 x 35mm) |
| Pressure: |
Operating |
0 to 100 psi (690 kpa) maximum |
| Static Burst Rating |
700 psi (4,830 kpa) for complete assembly |
| Flow: |
Both Valve Blocks |
7.2 gpm @ 60 psi (27.0 l/m @ 4 bar) |
| Construction: |
Valve Bodies |
Chrome Plated Brass |
| Seals |
Silicone or E.P.D.M. |
| Control Tubing |
1/8 O.D. 3 tube bundle (high density polyurethane) |
| Kick Plate |
18g #4 stainless steel top, aluminum base |
| Euro Foot Activated |
Housing - chrome or nickel plated brass housing;
cap - chrome or nickel plated brass; |
| |
Foot Probe - polyurethane |
| Filtration: |
Control Circuit |
25 micron |
| Main Port |
greater than .060" (1.5mm) |
Connections
Valve Blocks |
Inlet |
3/8" tube (for 3/8" compression) |
| Outlet |
Nut and sleeve, 3/8" compression |
Installation
Requirements: |
Cabinet Door (1710, 1720, 1722) |
Cabinet door of suitable height and construction for knee pressure, spring loaded hinges recommended. |
Kick Plate
(1750, 1752, 1740, 1742) |
Toe kick height of not less than 4" (10.2cm) horizontal clearance of at least 8" (20.4 cm) on one end of plate to allow for removal of stainles steel cover |
Euro Foot Activated
(1770, 1771, 1775, 1776) |
Toe kick height between 3" to 6" (75 to 150mm) polyurethane probe can be cut to length to fit by keeping the bottom of the probe between 1/2 to 1" above the finished floor. |
|
|
